 |
STC «Promprilad»:
Ukraine, 04080, Kyiv-080, P.B. 43
phone/fax: (044) 467-51-38,
467-51-39
EMail: ndt@ln.com.ua
Dynamic hardness gauge TDM-1 (release 1.5) is intended for high-speed measurements and hardness inspection of the structural, carbon and stainless steels and nonferrous metals made alloys, based on methods of Rockwell, Brinell, Vickers, Super-Rockwell, Shore and Leyb.
The dynamic hardness gauge is a compact device of TDM-2 type that is intended for express non destructive measurements and inspection of hardness of the structural, carbon steel and stainless steels and alloys made of nonferrous metals based on the Rockwell and Brinell scales.
Special-purpose eddy current flaw detector ВД-30НК-IVE is designed for detecting surface cracks in components made of ferromagnetic materials with rough-turned plate and curved surface
Densitometer for radiographic films entitled "Expert", is designed for measuring optical density of industrial radiographic films used during radiographic inspections of facilities.
Ultrasonic flaw detector UD3-71 is intended for defects detection, such as discontinuity and irregularities in materials, end items, semi-products and welded (soldered) joints; for the measurement of the flaw depth and coordinates; for the measurement of echo signals amplitude ratio; for the equivalent size measurement.
The flaw detector МД-4П (МД-4К) is designed for detecting surface flaws of discontinuity type in metals by means of the magnetic particle technique on the local sections of large-size components through originating stationary magnetic field applied.
Set of lenses with backlighting KLP-5 represents a power unit with a switch where the lenses with various magnification levels may be installed. The designed lens and the lamp are combined into one single device and may be easily replaced.
|
|
|
|
|
Dynamic hardness testers TDM-1, TDM-2 Are intended for express-measurements and hardness testing of structural carbon and stainless steels, alloys of non-ferrous metals under laboratory and field conditions. The technical specifications are represented in comparison.
Main technical specifications:
ТDM-1 |
Scale | Measurement range | Absolute error | Resolution |
HB | 90...450 | ±15 | 1.0 |
HRC | 20...70 | ±2,0 | 0.1 |
HRA | 70...85 | | 0.1 |
HRB | 30...99.9 | | 0.1 |
HV | 375...850 | ±15 | 1.0 |
HRN | 20...90 | | 0.1 |
HRT | 20...90 | | 0.1 |
HSD | 30...99.9 | ±2.0 | 1.0 |
HSC | 30...99.9 | | 0.1 |
HL | 300...900 | | 1.0 |
SP1 | 0...99.9 | | 0.1 |
SP2 | 0...99.9 | | 0.1 |
SP3 | 0...100 | | 1.0 |
SP4 | 0...100 | | 1.0 |
ТDM-2 |
HB | 90...450 | ±15 | 1.0 |
HRC | 20...70 | ±2,0 | 0.1 |
|
| | TDM-1 | TDM-2 |
Measurement results correction (depending on probe orientation) | 0°, 45°, 90°, 135°, 180° | 0°, 90°,180° |
Calibration | + | + |
Statistic measurement mode | from 3 to 99 | from3 to 5 |
Automatic translation from hardness into ultimate stress limit at stretching GOST 22761 | + | - |
Battery level indication | + | + |
High/Low limit alarm | sound and visual | visual |
Measurement results memory | 2000 measurements | - |
PC interface via RS232 Port and measurement procedure recording | + | - |
Time of continuous operation powered from batteries, at least | 80 hours | 25 hours |
Operating temperature range | -10...+40°C | -20...+50°C |
Protection GOST 14254 | IP40 | IP65 |
Dimensions | 157x84x30 mm | 85x126x35 mm |
Weight | 0.4 kg | 0.4 kg |
|
|
|
|
|
|
|
|
|
|
