 |
STC «Promprilad»:
Ukraine, 04080, Kyiv-080, P.B. 43
phone/fax: (044) 467-51-38,
467-51-39
EMail: ndt@ln.com.ua
Dynamic hardness gauge TDM-1 (release 1.5) is intended for high-speed measurements and hardness inspection of the structural, carbon and stainless steels and nonferrous metals made alloys, based on methods of Rockwell, Brinell, Vickers, Super-Rockwell, Shore and Leyb.
The dynamic hardness gauge is a compact device of TDM-2 type that is intended for express non destructive measurements and inspection of hardness of the structural, carbon steel and stainless steels and alloys made of nonferrous metals based on the Rockwell and Brinell scales.
Special-purpose eddy current flaw detector ВД-30НК-IVE is designed for detecting surface cracks in components made of ferromagnetic materials with rough-turned plate and curved surface
Densitometer for radiographic films entitled "Expert", is designed for measuring optical density of industrial radiographic films used during radiographic inspections of facilities.
Ultrasonic flaw detector UD3-71 is intended for defects detection, such as discontinuity and irregularities in materials, end items, semi-products and welded (soldered) joints; for the measurement of the flaw depth and coordinates; for the measurement of echo signals amplitude ratio; for the equivalent size measurement.
The flaw detector МД-4П (МД-4К) is designed for detecting surface flaws of discontinuity type in metals by means of the magnetic particle technique on the local sections of large-size components through originating stationary magnetic field applied.
Set of lenses with backlighting KLP-5 represents a power unit with a switch where the lenses with various magnification levels may be installed. The designed lens and the lamp are combined into one single device and may be easily replaced.
|
|
|
|
|
 Eddy Current Flaw detector VD-30
Special-purpose eddy current flaw detector ВД-30НК-IVE is designed for detecting surface cracks in components made of ferromagnetic materials with rough-turned plate and curved surface, and, principally, in railway equipment components in accordance with the "Technological Instruction on Tensile Tests and NDE of the railcars' components. 637-96 ПКБ ЦВ".
The flaw detector is intended for running under the laboratory and shop conditions, at overhaul plants of the Ministry for Communication Lines (MPS) and other machine- building enterprises.
Main technical specifications:
Flaw detection threshold (minimal flaw imitator) | (depth x wide) |
For surface roughness up to Rz 320 | up to 3.0 x 1.0 mm |
For surface roughness up to Ra 1.25 | up to 0.5 x 0.05 mm |
Testing surface curvature radius | at least 10 mm |
Probe lift off | up to 3 mm |
Mode of tuning out from influencing factors (surface curvature, piece border, probe lift off, slope angle of a transducer to the surface) | automatic |
Service functions: | Display backlighting.
Sound and visual flaw notification.
Crack depth evaluation.
5 testing modes. |
Time of continuous operation powered from batteries | at least 25 hours |
Operating temperature range | from -10 to 45 °C |
Dimensions | 157x84x30 mm |
Weight | 0.35 kg | |
Supplement set:
Electronic unit | 1 |
Probe with cable | 1 |
Spare caps for eddy current probes | 5 |
Battery unit (built in) | 1 |
Battery charger | 1 |
Calibration block ОSО2353.01 | 1 |
Lift off imitator | 2 |
Headphones | 1 |
Leather casing | 1 |
Packing case | 1 |
Documentation VD-30NK.23535778.01.00.00PS | 1 | |
|
|
|
|
|
|
|
|
|
